3.1. Usage Recommendations

• Security instructions

• Cleanliness and conservation
• Disposal of Components

Here are the recommendations for the correct and safe use of the system IsoView, we also highlight the main risks of its misuse. So we ask, again, a special attention to all points.

*The system IsoView must only be used in machinery for agricultural purposes, such as tractors, sprayers, planters, fertilizers, subsoilers, harvesters, among others.

*The system IsoView helps to guide the field operation, but the operator remains in command and must always be alert and in full control of the machinery to avoid possible obstacles or areas that have become unsafe, for example floods or fallen trees. The operator is ultimately responsible for the safe operation of this equipment..

*This safety information only pertains to the equipment of Agres IsoView and is not a substitute for other customary safe work practices..

*Keep the rear connectors of the Monitor and cables that are not being used covered to prevent dirt accumulation or moisture ingress..

*the connector usb, located on the right side of the screen, it is used only to download or upload files from the IsoView via pen drive (portable memory). NOT USE to connect other equipment, such as cell phones, flashlights, among others, as there is a risk of spoiling (damaging) the monitor.

!check with our Support and Technical Assistance or Representative the correct way to install the system IsoView on the agricultural implement. Non-recommended changes to the machinery can cause malfunctions and safety failures.

!The system IsoView NOT it must be handled by people who have not been trained and are unaware of its correct operation. Incorrect handling can cause personal injury, malfunctions and property damage..

!Do not use the system during thunderstorms. There is a great risk of electrical discharges reaching the system, with possible physical damage to people and equipment.

! Farmer, just use the system IsoView having been trained and being aware of its correct operation, possessing a suitable driving license in accordance with the regulations of the country, being aware of the operation of the machinery and necessary configuration to carry out the work in the field. Incorrect operation can cause personal injury, malfunction and property damage..

!Make sure vehicle power is off when connecting components, cables, or options to the system IsoView.

!Make sure the power supply is turned off before servicing or repairing the vehicle or implements, i.e. the master switch is off or the ignition key is with you..

!Before charging the tractor battery, always break the connection between the tractor and the tractor monitor. IsoView, unplugging the power cable just behind the screen.

!Before welding parts on your tractor or an attached or mounted accessory, always disconnect power to the tractor monitor. IsoView, unplugging the power cable just behind the screen.

!Do not make any unauthorized changes to the product. Unauthorized alterations and inappropriate use of the product pose a risk not only to the functionality of the product, but also to the life and safety of the operator. Any change that is not described in the product documentation is considered unauthorized..

!Incorrect connection of the power supply can cause serious injuries and damage to people or equipment..

!Farmer, before handling any hazardous substances make sure proper precautions have been taken. Always read the Material Safety Data Sheet before starting work.

!During Spray Simulation and Spray Diagnostics, the machine will be active and operational. Take all necessary precautions to ensure safety. Failure to do so could result in serious injury or death..

!Material in the spray tank will be released during Spray Simulation and Spray Diagnostics. Make sure that the location is environmentally appropriate and that people nearby are informed, properly protected and safe for this maneuver.

! Always check that any accessory suspended from the vehicle is fully lowered (close to the ground) before starting repair or maintenance work..

! The vehicle and implement parts can get hot during operation or maintenance and can also be pressurized, so be careful and consult the vehicle and implement manuals for the procedure you should follow..

!Always wear suitable protective clothing for yourself and the people involved in the task at hand, and don’t forget to check that the environmental conditions are appropriate..

!Do not operate the system IsoView near explosive equipment or materials without proper guidance from a hazardous goods technical expert.

!A Agres cannot guarantee the accuracy, completeness, continuity, or availability of Signal Correction services GPS/GLONASS (GNSS) or RTK, as they are services provided by third parties and may be affected by problems in reception of satellite signals from these companies.
In the event of instability in these services, to avoid possible risks to the driver and material damage or injury to third parties, disable the guidance system and take manual control of the vehicle until conditions normalize.

!The system IsoView it must not be used by an operator under the influence of alcohol, drugs or medication that restricts his senses or motor reflexes. Seek medical advice and follow their recommendations.

Your Responsibilities and Obligations

!It’s from YOUR RESPONSIBILITY read and understand the safety information and other instructions in this manual before operating the equipment. remember that YOU is the key to security. Good practices not only protect you, but also the people around you.

!If in doubt, contact our Support and Technical Assistance

The following actions are not recommended under penalty of Loss of Warranty:

* ⇒ Utilizar o equipamento fora das recomendações estipuladas neste manual;
⇒ Utilizar o equipamento em conjunto com acessórios de outros fabricantes não homologados ou sem aprovação do nosso Support and Technical Assistance;
⇒ Abrir ou desmontar partes do equipamento utilizando ferramentas, exceto se autorizado expressamente pelas equipes de Support and Technical Assistance;
⇒ Modificar os componentes do sistema, como chicotes e seus conectores;
⇒ Utilizar o equipamento danificado ou com avarias visíveis.