Near the navigation screen bottom is the information board. Through this board is possible to view several important information during navigation operation, without the need to return to IsoView system configuration menus.
In the navigation screen composition, the information board 
is shown as in the following image. When pressing the information button 
, the information page shown in the board changes.
The following are images of pages sequence in ISO 31 system information board, including the description of each item in its composition.
Note: The page 
is shown only for irrigation operation.
| Page | Item | Description |
|---|---|---|
| |
 |
Satellites Signal Quality icon |
 |
RTK correction quality icon | |
 |
Paid correction signal quality icon | |
| Differential Age | Time in seconds since last signal correction message (when configured) | |
| Base Distance | Distance from RTK base (when configured) to GNSS antenna | |
| |
Dist. Traveled | Operation distance traveled so far |
| Total area | Boundary total area | |
| Applied Area | Applied area | |
| Remaining Area | Difference between boundary total area and applied area | |
| Applied Volume | Applied volume | |
| Remaining Volume | Difference between total volume to cover the boundary and applied volume | |
 |
Field | Field file name used |
| Event | Event file name used | |
| Operation | Operation being performed | |
| Culture | Culture name | |
 |
Machine | Configured machine name |
| Implement | Configured value of implement width parameter (for spraying, includes the nozzles number) | |
| Overlay | Configured value of overlap parameter | |
| Dist. Implement | Configured implement value of antenna distance parameter | |
| |
Maximum Distance | Value of Maximum distance parameter, configured in  |
| Dist. until the alert | Distance from irrigation application start to alert distance, set in  |
|
| Limit | Remaining distance to reach Maximum Distance (hose length) | |
| Odometer | Distance traveled since pressing the odometer reset button  |
|
 |
Operator | Configured operator name |
| DD / MM / YYYY – HH: MM | Current date and time | |
| Working time | Total work time since event opening | |
| Effective Time | Effective working time, in which there has been application | |
 |
A-Lon | Longitude in degrees of point A of straight guide |
| A-Lat | Latitude in degrees of point A of straight guide | |
| B-Lon | Longitude in degrees of point B of straight guide | |
| B-Lat | Latitude in degrees of point B of straight guide | |
| Heading | Straight guide heading angle | |
| Distance A-B | Distance between straight guide points A and B | |
 |
Lon | Longitude in degrees of current GNSS point |
| Lat | Latitude in degrees of current GNSS point | |
| Altitude | Altitude in meters of current GNSS point | |
| HDOP | Horizontal dilution precision of GNSS | |
| Visible Sat. | Number of visible GNSS satellites | |
| Used Sat. | Number of GNSS satellites used |
In Spraying operation, by pressing the spraying settings button 
on the navigation screen, the information board assumes for a short time the configuration shown on page of the image below, containing information related to the application. After, the information board returns to its initial state .
| Page | Item | Description |
|---|---|---|
| |
|
Satellites Signal Quality icon |
| |
RTK correction quality icon | |
| |
Paid correction signal quality icon | |
| Differential Age | Time in seconds since last signal correction message (when configured) | |
| Base Distance | Distance from RTK base (when configured) to GNSS antenna | |
| |
Flow | Fluid flow rate through the flowmeter, in L/min |
| Pressure | Calculated spraying system pressure | |
| Tank Level | Current spraying tank level, in L | |
| Applied Volume | Total volume of fluid applied in the current event | |
| Target Rate1 | Fixed target rate 1 configured in the selected spraying job | |
| Target Rate1 | Fixed target rate 2 configured in the selected spraying job |
