Power Connection
| Power Connector Plug |
| Part Number |
Degson 8EDGK-35-03P-11 |
| Wire Size |
28 – 14 AWG (0.2 – 1.5 mm 2) |
| Strip Length |
5 – 6 mm |
Electrical Ratings
| Power supply voltage |
24.0V +/- 10% |
| Input Protection Rating |
Class III |
| Standby current consumption |
< 120mA |
| Motor Starting Current |
≤ 3A per Motor |
| Motor Rated Current |
≤ 2.5A per Motor |
Environmental Ratings
!Operating outside these parameters may result in permanent ConveyLinx-ECO Module failure or unexpected device behavior
| Minimum Operating Voltage |
21 |
| Maximum Operating Voltage |
30V |
| Storage temperature |
-25ºC to 70º C ( -13ºF to 160ºF) |
| Ambient Operating temperature |
0ºC to 40ºC ( 32°F to 104°F) |
| Humidity |
5% to 95% non-condensing |
| Vibration |
0.152 mm (0.006 in.) displacement, 1G peak |
| Mechanical Shock |
20G peak for 10ms duration (1.0 ms) |
| Enclosure IP Rating |
IP20 |
Certifications & Standards
| BDS EN 61131-2:2008 |
Programmable controllers — Part 2: Equipment requirements and tests |
| BDS EN 61000-6-2:2006 |
Electromagnetic compatibility (EMC) — Part 6-2: Generic standards – Immunity for industrial environments |
| BDS EN 61000-6-4:2007+A1:2011 |
Electromagnetic compatibility (EMC) — Part 6-4: Generic standards – Emission standard for industrial environments |
| BDS EN 55016-2-1:2009+A1:2011 |
Specification for radio disturbance and immunity measuring apparatus and methods Part 2-1 Methods of measurement of disturbances and immunity. Conducted disturbance measurements |
| BDS EN 55014-1:2007+A1:2009 +A2:2011 |
Electromagnetic compatibility – Requirements for household appliances, electric tools and similar apparatus — Part 1: Emission |
| BDS EN 61000-4-2:2009 |
Electromagnetic compatibility (EMC) Part 4-2: Electromagnetic discharge Immunity test |
| BDS EN 61000-4-4:2012 |
Electromagnetic compatibility (EMC) Part 4-4 Electrical fast transient/burst immunity test. |
| BDS EN 61000-4-5:2007 |
Electromagnetic compatibility (EMC) Part 4-5 Surge immunity test. |
| BDS EN 61000-4-6:2009 |
Electromagnetic compatibility (EMC) Part 4-6 Immunity to conducted disturbances, induced by radio-frequency field |
| BDS EN 61000-4-11:2009 |
Electromagnetic compatibility (EMC) Part 4-11 Voltage dips, short interruptions and voltage variations immunity tests |
Sensor Port
| Sensor Connector Plug |
| Part Number |
Degson 8EDGK-25-04P-11 |
| Wire Size |
28 – 20 AWG (0.2 – 0.5 mm 2) |
| Strip Length |
5 – 6 mm |
Each Module is equipped with two removable cage-clamp style plug connectors. These are used to connect a photo sensor and an optional Aux input device to the module. Both of these inputs are auto-sensing for PNP or NPN circuit type such that both sourcing and sinking current will activate the input based upon the following conditions:
| Minimum ON Current |
1.5 mA |
| Maximum OFF Current |
0.4 mA |
Sensor Port 24VDC (Pin 1) and GND (Pin 3)
Pin 1 of each Sensor Port provides 24V for powering up a sensor device and/or for supplying the load for the AUX input. The available current for the two ports on the module is limited internally by a solid-state fuse. The maximum combined current consumption for the two sensor ports is 100 mA.
!Current in excess of 100mA drawn from the sensor port’s 24V pin may cause permanent damage to the sensor detection circuit. Care should be taken to avoid excess loads, short circuits and miss-wiring of the sensor port.
Motor Port
| Supported motor types |
3 phase BLDC motors with 3 Hall Effect sensors |
| PWM frequency |
25kHz +/- 0.1% |
| Maximum starting current |
3A per Motor Port |
| Maximum rated current |
2.5A per Motor Port |
| Motor Protection* |
Coil-to-coil short, coil-to-Vcc short, overheating, over-voltage, under-voltage, stall sensing and protection |
!*During normal operation as an MDR port, the internal protection circuitry is not capable of detecting a short-circuit between a BLDC coil output and ground. Such a short-circuit will cause damage to the high-side bridge transistors. When operating these outputs as general purpose outputs, the high-side transistors are disabled, so a pin-to-ground short-circuit is not an issue
Motor Ports in Digital IO Mode as Outputs
Motor Coil Pins 3, 4, & 5
In certain modes of operation (PLC I/O and ConveyLogix PLC), Pins 3,4, and 5 can each be independently switched on and off as general purpose digital outputs. Any individual pin can sink up to 1A to ground in these modes, but the total for all 3 pins combined cannot exceed 1.5A. In general purpose I/O mode, these pins cannot source current.
Ethernet
• 3 port integrated switch ( 2 external ports and 1 port for the on-board processor)
• Automatic speed setup (10Base-T / 100Base-TX)
• Automatic duplex configuration (Full / Half)
• Automatic straight/crossover cable detection ( Auto MDI/MDI-X)
• PAUSE frame support
• Back pressure flow control support
• Maximum segment length: 100m / 328ft
Supported Protocols
• Modbus/TCP
• EtherNet/IP
• Profinet IO
Post your comment on this topic.