English
Japanese
EZ-Qube Reference Manual
4.1
4.1
3.0
3.1
4.0
2.0
Table of Contents
EZ-Qube Reference Manual
4.1
EZ-Qube Reference Manual — 4.1
EZ-Qube Reference Manual — 3.0
EZ-Qube Reference Manual — 3.1
EZ-Qube Reference Manual — 4.0
EZ-Qube Reference Manual — 2.0
1.
EZ-Qube Controller
1.1.
About This Manual
1.2.
Glossary of Terms
2.
Module Hardware
2.1.
Identifying Module Components
2.1.1.
EZ-Qube
2.1.2.
EZ-Qube-HTBF
2.1.3.
EZ-Qube-W
2.2.
Mounting Dimensions
2.3.
Mounting Considerations
2.4.
Power Connector
2.5.
Motor Connector
2.6.
I/O Connector
2.7.
Inspection and Cleaning
2.8.
Technical Specifications
2.9.
Ordering Information
3.
Module Wiring
3.1.
Power Supply
3.2.
Proper Motor Grounding Practice
3.3.
Run/Reverse Inputs
3.3.1.
Single Module
3.3.2.
Multiple Modules from Single Signal
3.3.3.
Multiple Modules from Individual Signals
3.4.
0-10V Analog Input
3.5.
Error Output
3.5.1.
PNP Versions
3.5.2.
NPN Versions
3.6.
Speed Output
3.6.1.
PNP Versions
3.6.2.
NPN Versions
4.
DIP Switch Settings
4.1.
CONFIG DIP Switch
4.1.1.
Electronic Holding Brake Settings
4.1.2.
Motor Performance Settings
4.2.
SPEED DIP Switch
4.2.1.
0-10V Analog Speed
4.2.2.
Speed Calculation
4.3.
ACC/DEC DIP Switch
4.3.1.
Accel/Decel Equal
4.3.2.
Decel Equal 2 x Accel
4.3.3.
Accel/Decel Time Formula
5.
EZ-Qube-W & EZ-Qube-W-Ai Bluetooth Set-Up
5.1.
Motor & Holding Brake Settings
5.2.
Speed Settings
5.3.
Input / Output Signal Settings
6.
Operation
7.
Output Signals & LED Indicators
7.1.
Pulse Speed Output
7.2.
Error Output and LED Status
7.2.1.
Power Supply ON with Motor Connected
7.2.2.
Motor Not Connected
7.2.3.
Power Supply Voltage > 32V
7.2.4.
Voltage Drop Below 18V and Voltage Drop Below 13V
7.2.5.
Voltage Over 32V Due to Motor Overspeed
7.2.6.
Normal Operation with Motor Running then Reverse Signal
7.2.7.
Motor Current Exceeding Peak Limit
7.2.8.
Over Current with PWM Limiting
7.2.9.
Motor Stalled with Self Stop
7.2.10.
Motor Overload with Self Stop
7.2.11.
Module Over Heat with Self Stop
7.2.12.
Motor Not Running when RUN is ON
7.2.13.
Motor Phases Error Detected
8.
Internal Jumper Settings
Download as PDF
2.2.
Mounting Dimensions
2.1.3.
EZ-Qube-W
2.3.
Mounting Considerations
Module Hardware
/
Mounting Dimensions
● EZ-Qube-P
● EZ-Qube-N
● EZ-Qube-P-MR
● EZ-Qube-P-J
● EZ-Qube-HTBF-P
● EZ-Qube-HTBF-N
● EZ-Qube-W
● EZ-Qube-W-Ai
2.1.3.
EZ-Qube-W
2.3.
Mounting Considerations